| Item |
Standard |
Limit |
|||
| Timing belt |
|||||
| Auto-tensioner rod extension length (with timing belt installed) mm |
2.3 - 7.6 |
- |
|||
| Auto-tensioner rod extension length (when free) mm |
14.5 |
- |
|||
| Auto-tensioner rod retraction length (when pressed with force of 98 - 196 N·m) mm |
Less than 1 |
- |
|||
| Rocker arm and camshaft |
|||||
| Valve clearance mm |
Intake |
0.09 |
- |
||
| Exhaust |
0.14 |
- |
|||
| Cam height mm |
Intake |
35.47 |
34.97 |
||
| Exhaust |
35.41 |
34.91 |
|||
| Cylinder head and valves |
|||||
| Flatness of gasket surface mm *Grinding is not suitable for correction. |
0.05 |
*0.2 |
|||
| Cylinder head overall height mm |
129.9 - 130.1 |
- |
|||
| Cylinder head bolt nominal length mm |
- |
93 |
|||
| Valve stem diameter mm |
Intake |
5.965 - 5.980 |
- |
||
| Exhaust |
5.950 - 5.965 |
- |
|||
| Valve thickness of valve head mm (margin) |
Intake |
1.3 |
0.8 |
||
| Exhaust |
1.5 |
1.0 |
|||
| Valve length mm |
Intake |
107.58 |
107.08 |
||
| Exhaust |
107.98 |
107.48 |
|||
| Valve spring free height mm |
54.3 |
53.3 |
|||
| Valve spring load/installed height N/mm |
230/40.5 |
- |
|||
| Valve spring cut-of-squareness |
2° or less |
Max. 4° |
|||
| Valve seat contact width mm |
1.1 - 1.5 |
- |
|||
| Valve stem-to guide clearance mm |
Intake |
0.020 - 0.047 |
0.10 |
||
| Exhaust |
0.035 - 0.062 |
0.15 |
|||
| Valve face angle |
45° - 45.5° |
- |
|||
| Oil pan and oil pump |
|||||
| Balancer shaft oil clearance mm |
Front |
Right |
0.02 - 0.05 |
- |
|
| Left |
0.02 - 0.06 |
- |
|||
| Rear |
0.06 - 0.10 |
- |
|||
| Oil pump tip clearance mm |
0.11 - 0.24 |
- |
|||
| Oil pump side clearance mm |
0.04 - 0.10 |
- |
|||
| Oil pump body clearance mm |
0.10 - 0.18 |
0.35 |
|||
| Piston and connecting rod |
|||||
| Piston ring end gap mm |
No. 1 ring |
0.30 - 0.45 |
0.8 |
||
| No. 2 ring |
0.30 - 0.45 |
0.8 |
|||
| Oil ring |
0.25 - 0.45 |
0.8 |
|||
| Piston ring-to-ring groove clearance
mm |
No. 1 ring |
0.06 - 0.11 |
0.15 |
||
| No. 2 ring |
0.05 - 0.08 |
0.15 |
|||
| Oil ring |
0.02 - 0.07 |
0.10 |
|||
| Oil clearance at crankshaft pins mm |
0.030 - 0.055 |
0.10 |
|||
| Connecting rod big end side clearance mm |
0.10 - 0.25 |
0.40 |
|||
| Crankshaft and cylinder block |
|||||
| Crankshaft end play mm |
0.05 - 0.25 |
0.45 |
|||
| Oil clearance at crankshaft journal mm |
0.040 - 0.055 |
0.10 |
|||
| Cylinder block gasket surface warp mm |
0.05 |
0.10 |
|||
| Cylinder I.D. mm |
91.10 - 91.13 |
- |
|||
| Cylindricity mm |
- |
0.02 |
|||
| Cylinder-to-piston clearance mm |
0.03 - 0.05 |
- |
|||
| note | O.D.: Outer diameter I.D.: Inner diameter |