Terminal No.
|
Check item
|
Inspection condition
|
Standard value
|
1
|
UD solenoid valve
|
- Engine: Idling
- Selector lever position: D (1st gear)
|
System voltage
|
- Engine: Idling
- Selector lever position: P
|
6 - 9 V
|
2
|
Solenoid valve power supply
|
Ignition switch: LOCK (OFF)
|
1 V or less
|
Ignition switch: ON
|
System voltage
|
3
|
Solenoid valve power supply
|
Ignition switch: LOCK (OFF)
|
1 V or less
|
Ignition switch: ON
|
System voltage
|
7
|
A/T fluid temperature warning lamp
|
Ignition switch: LOCK (OFF) to ON
|
1 V or less to system voltage (after several seconds have elapsed)
|
9
|
4LLc operation detection switch <4WD>
|
Ignition switch: ON Transfer lever: 4LLc
|
1 V or less
|
Ignition switch: ON Transfer lever: Other than the above
|
System voltage
|
11
|
Power supply voltage
|
Always
|
System voltage
|
12
|
Earth
|
Always
|
1 V or less
|
13
|
Earth
|
Always
|
1 V or less
|
14
|
Overdrive solenoid valve
|
- Engine: Idling
- Selector lever position: D (Overdrive switch: ON)
|
System voltage
|
- Engine: Idling
- Selector lever position: P
|
6 - 9 V
|
15
|
Damper clutch control solenoid valve
|
- Engine: Idling
- Selector lever position: P
|
System voltage
|
16
|
Second solenoid valve
|
- Engine: Idling
- Selector lever position: 2
|
System voltage
|
- Engine: Idling
- Selector lever position: P
|
6 - 9 V
|
20
|
Ignition switch
|
Ignition switch: LOCK (OFF)
|
1 V or less
|
Ignition switch: LOCK (OFF) to ON
|
System voltage to 1 V or less (after several seconds have elapsed)
|
24
|
Power supply
|
Always
|
System voltage
|
25
|
Earth
|
Always
|
1 V or less
|
26
|
Earth
|
Always
|
1 V or less
|
31
|
Input shaft speed sensor
|
- Measure between terminals 31 and 43 with an oscilloscope.
- Engine: 2,000 r/min
- Selector lever position: D (Overdrive switch: ON)
|
Refer to , Inspection Procedure Using an Oscilloscope.
|
32
|
Output shaft speed sensor
|
- Measure between terminals 32 and 43 with an oscilloscope.
- Engine: 2,000 r/min
- Selector lever position: D (Overdrive switch: ON)
|
Refer to , Inspection Procedure Using an Oscilloscope.
|
38
|
Backup power supply
|
Always
|
System voltage
|
43
|
Sensor earth
|
Always
|
1 V or less
|
44
|
A/T fluid temperature sensor
|
A/T fluid temperature: 20°C
|
3.8 - 4.0 V
|
A/T fluid temperature: 40°C
|
3.2 - 3.4 V
|
A/T fluid temperature: 80°C
|
1.7 - 1.9 V
|
55
|
Inhibitor switch: P
|
- Ignition switch: ON
- Selector lever position: P
|
System voltage
|
- Ignition switch: ON
- Selector lever position: Other than above
|
1 V or less
|
56
|
Inhibitor switch: N
|
- Ignition switch: ON
- Selector lever position: N
|
System voltage
|
- Ignition switch: ON
- Selector lever position: Other than above
|
1 V or less
|
57
|
Overdrive switch
|
- Ignition switch: ON
- Overdrive switch: ON
|
1 V or less
|
- Ignition switch: ON
- Overdrive switch: OFF
|
System voltage
|
58
|
Inhibitor switch: L
|
- Ignition switch: ON
- Selector lever position: L
|
System voltage
|
- Ignition switch: ON
- Selector lever position: Other than above
|
1 V or less
|
62
|
Low-reverse solenoid valve
|
- Engine: Idling
- Selector lever position: P
|
System voltage
|
- Engine: Idling
- Selector lever position: 2
|
6 - 9 V
|
66
|
Inhibitor switch: R
|
- Ignition switch: ON
- Selector lever position: R
|
System voltage
|
- Ignition switch: ON
- Selector lever position: Other than above
|
1 V or less
|
67
|
Inhibitor switch: D
|
- Ignition switch: ON
- Selector lever position: D
|
System voltage
|
- Ignition switch: ON
- Selector lever position: Other than above
|
1 V or less
|
68
|
Inhibitor switch: 2
|
- Ignition switch: ON
- Selector lever position: 2
|
System voltage
|
- Ignition switch: ON
- Selector lever position: Other than above
|
1 V or less
|
69
|
Vehicle speed sensor <2WD>
|
Vehicle: Slowly moving forward
|
Alternates between 0<=>Approx. 5 V
|
71
|
A/T control relay
|
Ignition switch: OFF
|
1 V or less
|
Ignition switch: ON
|
System voltage to 1 V or less (after several seconds have elapsed)
|
72
|
Earth
|
Always
|
1 V or less
|