Tool
|
Number
|
Name
|
Use
|
|
MB992080
|
Belt tension meter set
a: Belt tension meter b: Microphone assembly
|
Drive belt tension check
|
|
MB991955
a: MB991824 b: MB991827 c: MB991910 d: MB991911 e: MB991825 f: MB991826
|
M.U.T.-III sub assembly
a: Vehicle communication interface (V.C.I.) b: M.U.T.-III USB cable c: M.U.T.-III main harness A (Vehicles with CAN communication system) d: M.U.T.-III main harness B (Vehicles without CAN communication system) e: M.U.T.-III measurement adapter f: M.U.T.-III trigger harness
|
caution |
For vehicles with CAN communication,
use M.U.T.-III main harness A to send simulated vehicle speed. If you connect M.U.T.-III main harness
B instead, the CAN communication does not function correctly.
|
- Checking the idle speed
- Erasing diagnosis code
|
|
MB992188
|
Fuel injection pipe wrench
|
Removal and installation of fuel injection pipe assembly
|
|
MB992852
- Spare part: MB992872
|
Valve adjusting feeler gauge
- Spare part: Feeler gauge tip set (0.14 mm)
|
Check and adjustment of inlet valve clearance
|
|
MB991477
|
Valve adjusting socket
|
Adjustment of inlet valve clearance
|
|
MB992046
|
Valve adjusting socket
|
Adjustment of exhaust valve clearance
|
|
MB992285
|
Compression press test adapter
|
Measurement of compression pressure
|
|
MB992276
|
Drive belt remover
|
Water pump drive belt removal
|
|
MB990767
|
Front hub and flange yoke holder
|
Holding the crankshaft pulley
|
|
MD998754
|
Pin
|
|
MB991956
|
Engine hanger plate
|
Supporting the engine and transmission assembly
note |
Special tool MB991454 is a part of engine hanger attachment set MB991453.
|
|
|
MB991454
|
Engine hanger balancer
|
|
MB991527
|
Hanger
|
|
MB991895
|
Engine hanger
|
When the engine hanger is used: Supporting the engine assembly
during removal and installation of the crankshaft pulley, timing chain case assembly or transmission assembly
|
|
MB991928
a: MB991929 b: MB991930 c: MB991931 d: MB991932 e: MB991933 f: MB991934
|
Engine hanger
a: Joint (50) ×
2 b: Joint (90) ×
2 c: Joint (140) ×
2 d: Foot (standard) ×
4 e: Foot (short) ×
2 f: Chain and hook assembly
|
|
MB992288
|
Drive belt installer
|
Water pump drive belt installation
|
|
MB992289
|
Injector and fuel pipe remover
|
Fuel injector and common rail assembly removal
|
|
MB992333
|
Nozzle gasket remover
|
Fuel injection nozzle gasket removal
|
|
MB991614
|
Angle gauge
|
- Fuel injector holder bolt installation
- Flywheel bolt installation
|
|
MD998772
|
Valve spring compressor
|
Valve spring compression
|
|
MB992090
|
Retainer holder attachment
|
|
MB992283
|
Retainer holder D
|
|
MB992085
|
Valve stem seal pliers
|
Valve stem seal removal
|
|
MH062687
|
Installer inlet ring
|
Crankshaft rotation
|
|
MD998775
|
Valve stem seal installer
|
Valve stem seal press-fitting <exhaust side>
|
|
MB992284
|
Valve stem seal installer
|
Valve stem seal installation <inlet side>
|
|
MD998727
|
Oil pan FIPG cutter
|
Engine oil pan removal
|
|
MB991883
|
Flywheel stopper
|
Supporting the flywheel
|
|
MD998781
|
Flywheel stopper
|
Supporting the drive plate
|
|
MB991818
|
Oil seal installer
|
Crankshaft rear oil seal installation
|
|
MB990938
|
Installer bar
|
|
MB992290
|
Oil seal installer
|
Crankshaft front oil seal installation
|
|
MB992075
|
Handle
|