Code No. P0123: Throttle Position Sensor (main) Circuit High Input

OPERATION

A power voltage of 5 V is applied to the electronic-controlled throttle valve connector terminal from the engine-ECU connector terminal TPS5.
The power voltage is earthed to the engine-ECU connector terminal TPSE from the electronic-controlled throttle valve connector terminal.
The sensor signal is inputted to the engine-ECU connector terminal TPSM from the electronic-controlled throttle valve output terminal.

FUNCTION

The throttle position sensor converts the throttle valve position into voltage and inputs it into the engine-ECU.
The engine-ECU controls the throttle valve opening angle.

TROUBLE JUDGMENT

Check Condition

Ignition switch is "ON" position.

Judgement Criterion

Throttle position sensor (main) output voltage is more than 4.8 V.

FAIL-SAFE AND BACKUP FUNCTION

Throttle opening degree is restricted.
Throttle opening degree position is in default position if throttle position sensor (sub) fails.

PROBABLE CAUSES

Failed throttle position sensor (main)
Open/short circuit or harness damage in throttle position sensor circuit or loose connector contact
Failed engine-ECU

DIAGNOSIS PROCEDURE

STEP 1. M.U.T.-III data list

Data list reference table (Refer to ).

Item 13: Throttle position sensor (main)

Q. Is the check result normal?

	Intermittent malfunction (Refer to GROUP 00 - How to Use Troubleshooting/Inspection Service Points - How to Cope with Intermittent Malfunctions ).

	Go to Step 2.

STEP 2. Perform voltage measurement at electronic-controlled throttle valve connector.

Disconnect connector, and measure at harness side.
Ignition switch: "ON"
Voltage between terminal engine-ECU TPS5 line and body earth.

OK: 4.9 - 5.1 V

Q. Is the check result normal?

	Go to Step 5.

	Go to Step 3.

STEP 3. Check harness between electronic-controlled throttle valve connector terminal and engine-ECU connector terminal TPS5.

Check power supply line for open/short circuit.

Q. Is the check result normal?

	Go to Step 4.

	Repair or replace the connector, or repair the damaged harness wire.

STEP 4. M.U.T.-III data list

Data list reference table (Refer to ).

Item 13: Throttle position sensor (main)

Q. Is the check result normal?

	Intermittent malfunction (Refer to GROUP 00 - How to Use Troubleshooting/Inspection Service Points - How to Cope with Intermittent Malfunctions ).

	Replace the engine-ECU.

STEP 5. Perform resistance measurement at electronic-controlled throttle valve connector.

Disconnect connector, and measure at harness side.
Resistance between terminal engine-ECU TPSE line and body earth.

OK: Continuity (2 Ω or less)

Q. Is the check result normal?

	Go to Step 7.

	Go to Step 6.

STEP 6. Check harness between electronic-controlled throttle valve connector terminal and engine-ECU connector terminal TPSE.

Check earthing line for open circuit and damage.

Q. Is the check result normal?

	Go to Step 4.

	Repair or replace the connector, or repair the damaged harness wire.

STEP 7. Check harness between electronic-controlled throttle valve connector terminal and engine-ECU connector terminal TPS5.

Check power supply line for damage.

Q. Is the check result normal?

	Go to Step 8.

	Repair or replace the connector, or repair the damaged harness wire.

STEP 8. Check harness between electronic-controlled throttle valve connector terminal and engine-ECU connector terminal TPSM.

Check output line for open circuit and damage.

Q. Is the check result normal?

	Go to Step 9.

	Repair or replace the connector, or repair the damaged harness wire.

STEP 9. M.U.T.-III data list

Data list reference table (Refer to ).

Item 13: Throttle position sensor (main)

Q. Is the check result normal?

	Intermittent malfunction (Refer to GROUP 00 - How to Use Troubleshooting/Inspection Service Points - How to Cope with Intermittent Malfunctions ).

	Go to Step 10.

STEP 10. Replace the electronic-controlled throttle valve

After replacing the electronic-controlled throttle valve, reconfirm whether the diagnosis code is set.

Q. Is the diagnosis code set?

	Replace the engine-ECU.

	Check end.