Item No.
|
Inspection Item
|
Inspection condition
|
Normal condition
|
1
|
Starter switch (Ignition switch-ST)
|
Ignition switch: ON
|
OFF
|
Ignition switch: ST
|
ON
|
2
|
Ignition switch-IG
|
Ignition switch: ON
|
ON
|
4
|
Hood
|
Ignition switch: ON
|
Hood: Close
|
Close
|
Hood: Open
|
Open
|
5
|
AS&G OFF switch
|
Ignition switch: ON
|
AS&G OFF switch: Pressed
|
ON (only while the switch is pressed)
|
AS&G OFF switch: Released
|
OFF
|
6
|
Clutch monitoring switch (upper)
|
Ignition switch: ON
|
Clutch pedal: Depressed
|
ON
|
Clutch pedal: Released
|
OFF
|
7
|
Clutch interlock switch (bottom)
|
Ignition switch: ON
|
Clutch pedal: Fully depressed
|
ON
|
Clutch pedal: Released
|
OFF
|
8
|
Neutral position switch
|
Ignition switch: ON
|
Gearshift lever position: Neutral
|
ON
|
Gearshift lever position: Except neutral
|
OFF
|
9
|
DC/DC converter diagnostic signal*1
|
Ignition switch: ON
|
ON
|
10
|
Seat belt fasten status*2
|
Ignition switch: ON
|
Fasten the driver’s seat belt
|
Fastened
|
Do not fasten the driver’s seat belt.
|
Not Fastened
|
11
|
Engine-ECU AS&G system failure*3
|
Ignition switch: ON
|
OFF
|
12
|
Idle stop enable (A/C-ECU)
|
When auto stop prohibition signal is not received from A/C-ECU
|
Enable
|
When auto stop prohibition signal is received from A/C-ECU*4
|
Disable
|
13
|
Idle stop enable (engine-ECU)
|
When auto stop prohibition signal is not received from engine-ECU
|
Enable
|
When auto stop prohibition signal is received from engine-ECU*5
|
Disable
|
14
|
Brake vacuum sensor <4N1>
|
Engine: Idle operation after warm-up
|
- Turn the ignition switch ON after the engine
stops from the idling
- Depress the brake pedal several times
|
Increases whenever the brake pedal is depressed. (vacuum pressure
is reduced)
|
15
|
Ambient temperature
|
Ignition switch: ON or engine running
|
Ambient temperature: - 20°C
|
- 20°C
|
Ambient temperature: 0°C
|
0°C
|
Ambient temperature: 20°C
|
20°C
|
Ambient temperature: 40°C
|
40°C
|
Ambient temperature: 80°C
|
80°C
|
16
|
Atmospheric pressure <4N1>
|
Ignition switch: ON
|
Altitude: 0 m
|
101 kPa
|
Altitude: 600 m
|
95 kPa
|
Altitude: 1,200 m
|
88 kPa
|
Altitude: 1,800 m
|
81 kPa
|
17
|
Vehicle speed
|
Running at 40 km/h
|
Approximately 40 km/h
|
18
|
Accelerator pedal position
|
Ignition switch: ON
|
Release the accelerator pedal
|
0 %
|
Depress the accelerator pedal
|
Increases in response to the accelerator pedal depression stroke
|
Depress the accelerator pedal fully
|
98 % or more
|
19
|
Starter relay (output)
|
At auto start
|
ON
|
Except auto start status
|
OFF
|
20
|
Starter cut relay (output)
|
Ignition switch: ON (includes auto stop status)
|
ON
|
Engine: Cranking (includes the cranking of auto start status)
|
OFF
|
21
|
DC/DC converter control signal
|
Change vehicle status to auto stop status.*6
|
Clutch pedal: Depressed (this allows the engine to achieve
the auto start status)
|
At auto start, display status "OFF" is changed to "ON" for a second.
|
22
|
Idle stop enable (vehicle speed)
|
Drive the vehicle after the engine start, including
the engine start of the auto start.
|
When vehicle speed exceeds 5 km/h, display status "Disabled" should
be changed to "Enable"
|
23
|
Idle stop flag
|
Change vehicle status to auto stop status.*6
|
ON
|
Except auto stop status
|
OFF
|
24
|
AS&G OFF indicator lamp (output)*7
|
Ignition switch: ON
|
Press the AS&G OFF switch to turn OFF the AS&G system
|
Turn on
|
From the AS&G system OFF status, press the
AS&G OFF switch to turn ON the AS&G system
|
Turn off
|
25
|
AS&G indicator lamp (output)
|
During idling and driving (The idling stop operation standby
incomplete)
|
Turn off
|
During idling and driving (The idling stop operation standby
complete) *6
|
Turn on
|
or
- When the driver’s seat belt is not fastened
or
- During auto stop, the gearshift lever position is in other than neutral position
|
Turn on <=> Turn off (changes repeatedly)
|
35
|
Driver’s side door switch
|
Ignition switch: ON
|
Driver’s side door: Open
|
Open
|
Driver’s side door: Close
|
Close
|