DATA LIST REFERENCE TABLE


Item No.
 Inspection Item
 Inspection condition
 Normal condition
1
 Starter switch (Ignition switch-ST)
 Ignition switch: ON
 OFF
Ignition switch: ST
 ON
2
 Ignition switch-IG
 Ignition switch: ON
 ON
4
 Hood
 Ignition switch: ON
 Hood: Close
 Close
Hood: Open
 Open
5
 AS&G OFF switch
 Ignition switch: ON
 AS&G OFF switch: Pressed
 ON (only while the switch is pressed)
AS&G OFF switch: Released
 OFF
9
 DC/DC converter diagnostic signal*1
 Ignition switch: ON
 ON
10
 Seat belt fasten status*2
 Ignition switch: ON
 Fasten the driver’s seat belt
 Fastened
Do not fasten the driver’s seat belt.
 Not Fastened
11
 Engine-ECU AS&G system failure*3
 Ignition switch: ON
 OFF
15
 Ambient temperature
 Ignition switch: ON or engine running
 Ambient temperature: - 20°C
 - 20°C
Ambient temperature: 0°C
 0°C
Ambient temperature: 20°C
 20°C
Ambient temperature: 40°C
 40°C
Ambient temperature: 80°C
 80°C
17
 Vehicle speed
 Running at 40 km/h
 Approximately 40 km/h
18
 Accelerator pedal position
 Ignition switch: ON
 Release the accelerator pedal
 0 %
Depress the accelerator pedal
 Increases in response to the accelerator pedal depression stroke
Depress the accelerator pedal fully
 98 % or more
19
 Starter relay (output)
 At auto start
 ON
Except auto start status
 OFF
21
 DC/DC converter control signal
 Change vehicle status to auto stop status.*4
 Brake pedal: Depressed (this allows the engine to achieve the auto start status)
 At auto start, display status "OFF" is changed to "ON" for a second.
22
 Idle stop enable (vehicle speed)
 Drive the vehicle after the engine start, including the engine start of the auto start.
 When vehicle speed exceeds 5 km/h, display status "Disabled" should be changed to "Enable"
23
 Idle stop flag
 Change vehicle status to auto stop status.*4
 ON
Except auto stop status
 OFF
24
 AS&G OFF indicator lamp (output)*5
 Ignition switch: ON
 Press the AS&G OFF switch to turn OFF the AS&G system
 Turn on
From the AS&G system OFF status, press the AS&G OFF switch to turn ON the AS&G system
 Turn off
25
 AS&G indicator lamp (output)
 During idling and driving (The idling stop operation standby incomplete)
 Turn off
During idling and driving (The idling stop operation standby complete) *4
 Turn on
When any one of following cases is satisfied except for auto stop status.

  • When the hood is opened

  • When the driver’s seat belt is not fastened

  • When the driver’s door is opened
 Turn on <=> Turn off (changes repeatedly)
When any one of following cases is satisfied during auto stop status.

  • Selector lever position is P position and release the brake pedal

  • When the hood is opened

  • When the driver’s seat belt is not fastened and driver’s door is opened
 Turn on <=> Turn off (changes repeatedly)
27
 DC-DC OUT for powertrain (Input)*1
 Ignition switch: ON
 ON
28
 Brake hold signal (H/W)
 Change vehicle status to auto stop status.*4
 ON
Except auto stop status
 OFF
29
 Parking brake SW
 Parking brake: ON
 ON
Parking brake: OFF
 OFF
30
 Brake lamp SW
 Ignition switch: ON
 Depress the brake pedal
 ON
Release the brake pedal
 OFF
31
 Clutch status
  • Ignition switch: ON

  • selector lever: P or N position

 Open

  • Engine: Idle operation

  • selector lever: D or R position

 Engage
32
 Electric oil pump active status
 Change vehicle status to auto stop status.*4
 ON
Except auto stop status
 OFF
33
 Brake hold signal (CAN)
 Change vehicle status to auto stop status.*4
 ON
Except auto stop status
 OFF
34
 Engine status
 Ignition switch: ON
 Stall
Engine: Cranking (includes the cranking of auto start status)
 Cranking
Engine: Idle operation
 Run
35
 Driver’s side door SW
 Ignition switch: ON
 Driver’s side door: Open
 Open
Driver’s side door: Close
 Close
38
 T/M ECU AS&G system failure*6
 Ignition switch: ON
 OFF
39
 ASC ECU AS&G system failure*7
 Ignition switch: ON
 OFF
40
 Electric oil pump system failure*8
 Ignition switch: ON
 OFF
41
 DC-DC IN for powertrain (Output)
 Change vehicle status to auto stop status.*6
 Brake pedal: Depressed (this allows the engine to achieve the auto start status)
 At auto start, display status "OFF" is changed to "ON" for a second.
42
 Starter relay for AS&G (Output)
 Change vehicle status to auto stop status.*6
 Brake pedal: Depressed (this allows the engine to achieve the auto start status)
 At auto start, display status "OFF" is changed to "ON" for a second.
44
 Yaw rate sensor
 Stops the vehicle in a horizontal state
 -0.04 - 0.04 m/s2
When driving
 The value changes in the range between -1 to 1 m/s2
45
 Brake booster pressure
  • Ignition switch: ON

  • Depress the brake pedal a few times

 Whenever brake pedal is depressed, voltage increases (reduces vacuum).
note *1: If the DC/DC converter body or the DC/DC converter circuit is abnormal, "OFF" or "Failure" should be shown. If the communication error occurs between the AS&G-ECU and the DC/DC converter, "SNA" should be shown.
note *2: If the combination meter detects the seat belt malfunction, "Fault" should be shown. If the communication error occurs between the ETACS-ECU and the combination meter, "SNA" should be shown.
note *3: If the engine control system is abnormal, "ON" should be shown.
note *4: Check the auto stop condition and make a vehicle the state of the auto stop.
note *5: If the AS&G system is abnormal, "Turn on" and "Turn off" should repeatedly and alternately stay on the display.
note *6: If the CVT system is abnormal, "ON" should be shown.
note *7: If the ASC system is abnormal, "ON" should be shown.
note *8: If the electric oil pump system is abnormal, "ON" should be shown.

ASG-ECU monitoring items



Item No.
 Inspection item
 M.U.T.-III display descriptions
 Standards at each check
 Display range, and numeric value
12
 Idle Stop enable (A/C ECU)
  • Indicates the state of the auto stop prohibition signal from A/C-ECU. When the signal is received, "Disable" should be displayed.
  • If this happens, check the A/C-ECU permissions.

 Ignition switch: ON
 Enable / Disable
13
 Idle Stop enable (ENG ECU)
  • Indicates the state of the auto stop prohibition signal from engine-ECU. When the signal is received, "Disable" should be displayed.
  • If this happens, check the engine-ECU permissions.

 Ignition switch: ON
 Enable / Disable
26
 Idle stop disable timer
  • After the key/engine switch is used to start the engine, the AS&G-ECU counts down from 30 seconds. When the AS&G-ECU counts down to zero, a "0 sec" should stay on the display.

 After starting the engine
 30 - 0 sec
36
 Idle Stop enable (T/M ECU)
  • Indicates the state of the auto stop prohibition signal from CVT-ECU. When the signal is received, "Disable" should be displayed.
  • If this happens, check the CVT-ECU permissions.

 Ignition switch: ON
 Enable / Disable
37
 Idle Stop enable (ASC ECU)
  • Indicates the state of the auto stop prohibition signal from ASC-ECU. When the signal is received, "Disable" should be displayed.
  • If this happens, check the ASC-ECU permissions.

 Ignition switch: ON
 Enable / Disable
43
 Brake hold request mode flag
  • Indicates the status of the brake hold mode sent to the ASC-ECU.

 Change vehicle status to auto stop status.*1
 ON
note *1: Check the auto stop condition and make a vehicle the state of the auto stop.