Terminal number
|
Terminal code
|
Check item
|
Check conditions
|
Normal conditions
|
1
|
CANH
|
CAN bus line
|
-
|
-
|
2
|
SGND
|
Earth (for signal)
|
Always
|
1 V or less
|
3
|
-
|
-
|
-
|
-
|
4
|
LEDA
|
Engine switch LED (orange) ON signal
|
Power supply mode: ACC
|
System voltage
|
5
|
LEDG
|
Engine switch LED (green) ON signal
|
Power supply mode: ON
|
System voltage
|
6
|
LEDW
|
Engine switch LED (character illumination) ON signal
|
Always
|
System voltage
|
7
|
IG1
|
IG1 output signal
|
Power supply mode: ON
|
System voltage
|
Power supply mode: Other than ON
|
1 V or less
|
8 - 9
|
-
|
-
|
-
|
-
|
10
|
ACC
|
ACC output signal
|
Power supply mode: ACC
|
System voltage
|
Power supply mode: Other than ACC
|
1 V or less
|
11
|
IG2
|
IG2 output signal
|
Power supply mode: ON (Without cranking)
|
System voltage
|
Power supply mode: Other than ON
|
1 V or less
|
12
|
BKOS
|
Back-up power supply for KOS
|
When the engine switch is pressed to turn the power supply mode OFF
|
System voltage
|
13
|
+B1
|
Battery power supply
|
Always
|
System voltage
|
14
|
CANL
|
CAN bus line
|
-
|
-
|
15
|
PGND
|
Earth (for CPU)
|
Always
|
1 V or less
|
16
|
LIN
|
LIN bus line (local) for electric steering lock
|
-
|
-
|
17
|
PDSW
|
P position detection signal
|
Selector lever: P position
|
0 to 5 V (pulse signal)
|
Selector lever: Other than P position
|
1 V or less
|
18
|
-
|
-
|
-
|
-
|
19
|
SW2
|
Engine switch ON/OFF detection signal
|
When the engine switch is pressed
|
1 V or less
|
When the engine switch is not pressed
|
0 to 5 V (pulse signal)
|
20
|
-
|
-
|
-
|
-
|
21
|
PCK
|
Actuator driving permission monitoring signal
|
At engine start and when KOS power is OFF
|
1 V or less
|
Other than above
|
System voltage
|
22
|
-
|
-
|
-
|
-
|
23
|
ST
|
Starter output signal
|
Cranking
|
System voltage
|
Other than above
|
1 V or less
|
24
|
-
|
-
|
-
|
-
|
25
|
PCO
|
Power control output terminal for electric steering
lock
|
Power supply mode: OFF
|
System voltage
|
Power supply mode: Other than OFF
|
1 V or less
|
26
|
-
|
-
|
-
|
-
|
27
|
STP1
|
Stop lamp switch ON/OFF detection signal
|
When the brake pedal is depressed
|
System voltage
|
When the brake pedal is released
|
1 V or less (pulse signal)
|
28
|
-
|
-
|
-
|
-
|
29
|
SW1
|
Engine switch ON/OFF detection signal
|
When the engine switch is pressed
|
System voltage
|
When the engine switch is not pressed
|
1 V or less
|
30
|
-
|
-
|
-
|
-
|
31
|
IG2M
|
IG2 relay drive status detection signal
|
At ACC, OFF or during engine cranking
|
1 V or less
|
Other than above
|
System voltage
|
32
|
+B2
|
Battery power supply
|
Always
|
System voltage
|
)