Inspection Procedure
8: Either of the door mirror heater elements does not work.
|
COMMENTS ON TROUBLE SYMPTOM
|
|
If one of the door mirror heater elements does not work, the power supply or earth to
the element, or the element itself may be defective.
|
|
- Door mirror heater elements failed
- Wiring harness or connector failure
|
|
STEP 1. Determine a trouble spot.
|
|
Q.
Which of door mirror heater elements does not work?
|
|
RH side door mirror : Go to Step 2.
|
|
|
|
LH side door mirror : Go to Step 8.
|
|
|
|
STEP 2. Check of the heater element of the door mirror (RH)
|
|
Check the heater element of the door mirror (RH). (Refer to Heater Element Check .)
|
|
Q.
Is the check result normal?
|
|
Go to Step 3.
|
|
|
|
Replace the mirror glass of the door mirror assembly (RH).
|
|
|
|
STEP 3. Measure the resistance at the door mirror assembly (RH) connector.
|
|
(1)Disconnect the connector, and measure at the wiring harness side.
|
|
(2)Resistance between door mirror assembly (RH) connector (earth terminal) and body
earth OK: Continuity exists (2 Ω
or less)
|
|
Q.
Is the check result normal?
|
|
Go to Step 5.
|
|
|
|
Go to Step 4.
|
|
|
|
STEP 4. Check of open circuit in earth line between the door mirror
assembly (RH) connector and body earth.
|
|
Q.
Is the check result normal?
|
|
Intermittent malfunction (Refer to GROUP 00 - How to Use Troubleshooting/Inspection
Service Points - How to Cope with Intermittent Malfunction ).
|
|
|
|
Repair the connector(s) or wiring harness.
|
|
|
|
STEP 5. Measure the voltage at the door mirror assembly (RH) connector.
|
|
(1)Turn the ignition switch to the ON position.
|
|
(2)Turn on the rear window defogger switch.
|
|
(3)Disconnect the connector, and measure at the wiring harness side.
|
|
(4)Measure the voltage between door mirror assembly (RH) connector (power supply terminal)
and body earth. OK: System voltage
|
|
Q.
Is the check result normal?
|
|
Intermittent malfunction (Refer to GROUP 00 - How to Use Troubleshooting/Inspection
Service Points - How to Cope with Intermittent Malfunction ).
|
|
|
|
Go to Step 6.
|
|
|
|
STEP 6. Check of open circuit in DEFO-1&DEFO-2 line between
door mirror assembly (RH) connector and ETACS-ECU connector.
|
|
Q.
Is the check result normal?
|
|
Go to Step 7.
|
|
|
|
Repair the connector(s) or wiring harness.
|
|
|
|
STEP 7. Retest the system.
|
|
Check that the heater element of the door mirror (RH) functions normally.
|
|
Q.
Is the check result normal?
|
|
Intermittent malfunction (Refer to GROUP 00 -
How to Use Troubleshooting/Inspection
Service Points - How to Cope with Intermittent Malfunction ).
|
|
|
|
Replace the door mirror assembly (RH).
|
|
|
|
STEP 8. Check of the heater element of the door mirror (LH)
|
|
Check the heater element of the door mirror (LH). (Refer to Heater Element Check .)
|
|
Q.
Is the check result normal?
|
|
Go to Step 9.
|
|
|
|
Replace the mirror glass of the door mirror assembly (LH).
|
|
|
|
STEP 9. Measure the resistance at the door mirror assembly (LH) connector.
|
|
(1)Disconnect the connector, and measure at the wiring harness side.
|
|
(2)Measure the resistance between door mirror assembly (LH) connector (earth terminal)
and body earth. OK: Continuity exists (2 Ω
or less)
|
|
Q.
Is the check result normal?
|
|
Go to Step 11.
|
|
|
|
Go to Step 10.
|
|
|
|
STEP 10. Check of open circuit in earth line between the door mirror
assembly (LH) connector and body earth.
|
|
Q.
Is the check result normal?
|
|
Intermittent malfunction (Refer to GROUP 00 - How to Use Troubleshooting/Inspection
Service Points - How to Cope with Intermittent Malfunction ).
|
|
|
|
Repair the connector(s) or wiring harness.
|
|
|
|
STEP 11. Measure the voltage at the door mirror assembly (LH) connector.
|
|
(1)Turn the ignition switch to the ON position.
|
|
(2)Turn on the rear window defogger switch.
|
|
(3)Disconnect the connector, and measure at the wiring harness side.
|
|
(4)Voltage between door mirror assembly (LH) connector (power supply terminal) and
body earth. OK: System voltage
|
|
Q.
Is the check result normal?
|
|
Intermittent malfunction (Refer to GROUP 00 - How to Use Troubleshooting/Inspection
Service Points - How to Cope with Intermittent Malfunction ).
|
|
|
|
Go to Step 12.
|
|
|
|
STEP 12. Check of open circuit DEFO-1&DEFO-2 line between
door mirror assembly (LH) connector and ETACS-ECU connector.
|
|
Q.
Is the check result normal?
|
|
Go to Step 13.
|
|
|
|
Repair the connector(s) or wiring harness.
|
|
|
|
STEP 13. Retest the system.
|
|
Check that the heater element works normally.
|
|
Q.
Is the check result normal?
|
|
Intermittent malfunction (Refer to GROUP 00 - How to Use Troubleshooting/Inspection
Service Points - How to Cope with Intermittent Malfunction ).
|
|
|
|
Replace the door mirror assembly (LH).
|
|
|