Code No.B1612
Seat belt pre-tensioner (passenger’s side) (squib) system (shorted to squib circuit power
supply)
caution
If the diagnosis code B1612
is set to SRS-ECU, be sure to diagnose the CAN bus line.
OPERATION
Only when the frontal impact exceeding the threshold is simultaneously detected (turned
ON) by the front impact sensor as well as by the analogue G-sensor in SRS-ECU, the electric
current is supplied from SRS-ECU to the seat belt pre-tensioner (squib).
TROUBLE JUDGEMENT
The code is set when the input terminal of SRS-ECU seat belt pre-tensioner (passenger’s
side) (squib) is shorted to power supply.
PROBABLE CAUSES
Damaged wiring harness and connector
Seat belt pre-tensioner (passenger’s side) (squib) harness shorted to power
supply
Malfunction of SRS-ECU
DIAGNOSIS PROCEDURE
STEP 1. M.U.T.-III CAN bus diagnostics.
Use M.U.T.-III to diagnose the CAN bus lines.
Q.
Is the check result normal?
Go to Step 2.
Repair the CAN bus line (Refer to GROUP 54C - Troubleshooting ).
STEP 2. Check whether the diagnosis code is reset.
(1)Connect the negative battery terminal.
(2)After erasing the diagnosis code memory, check the diagnosis code again.
(3)Disconnect the negative battery terminal.
Q.
Is the diagnosis code No. B1612 set?
Go to Step 3.
Intermittent malfunction (Refer to GROUP 00 - How to Use Troubleshooting/Inspection
Service Points - How to Cope with Intermittent Malfunction ).
STEP 3. Diagnosis check by dummy resistor connection.
(1)Check that the negative battery terminal is disconnected. If the negative battery
terminal is connected, disconnect it.
(2)Use the flat-tipped screwdriver to pull out the locking button of harness side connector.
After releasing the lock, disconnect the seat belt pre-tensioner (passenger’s side) harness
side connector.
(3)Connect special tool dummy resistor (MB991865) to special tool resistor harness (MB991884). (4)Connect the special tool resistor harness to the seat belt pre-tensioner (passenger’s
side) harness side connector. (5)Connect the negative battery terminal. (6)After erasing the diagnosis code memory, check the diagnosis code again. (7)Disconnect the negative battery terminal.
Q.
Is the diagnosis code No. B1612 set?
Go to Step 4.
Replace the seat belt with pre-tensioner (passenger’s side) (Refer to ).
STEP 4. Voltage measurement at the SRS-ECU connector.
(1)Check that the negative battery terminal is disconnected. If the negative battery
terminal is connected, disconnect it.
(2)While pushing the part "A" indicated in the figure of the harness side connector, turn
the lock lever to the direction of the arrow to release the lock lever, and disconnect the SRS-ECU
connector.
(3)
danger
To release the SRS-ECU connector short spring in the following
operations, disconnect this seat belt pre-tensioner connector, and keep the squib circuit shorted.
Use the flat-tipped screwdriver to pull out the locking button of harness side connector.
After releasing the lock, disconnect the seat belt pre-tensioner (passenger’s side) harness
side connector.
(4)
caution
The short spring may not be released due to the insufficient insertion. Therefore, insert
the insulator for 4 mm or more.
Insert an insulator (width: 3 mm, thickness: 0.5 mm) such as cable tie between the PTA+,
PTA- line, and the short spring, and release the short spring. (5)Connect the negative battery terminal. (6)Ignition switch: ON (7)Take the measurements below at the SRS-ECU harness side connector.
Voltage between PTA+, PTA- line and body earth
OK: 1 V or less (8)Disconnect the negative battery terminal.
Q.
Is the check result normal?
Go to Step 5.
Repair the wiring harness PTA+, PTA- line between the SRS-ECU connector
and the seat belt pre-tensioner (passenger’s side) connector.
STEP 5. Check whether the diagnosis code is reset.
Q.
Is the diagnosis code No. B1612 set?
Replace SRS-ECU (Refer to ).
Intermittent malfunction (Refer to GROUP 00 - How to Use Troubleshooting/Inspection
Service Points - How to Cope with Intermittent Malfunction ).