CHECK WITH TERMINAL VOLTAGE




CONNECTOR: C-401




Terminal No.
 Terminal code
 Check item
 Check condition
 Normal condition
1
 -
 -
 -
 -
2
 DUL2
 Output to central door locking (for unlocking the passenger’s door)
 When the door lock actuators unlock the passenger’s door
 System voltage
3
 LP+3
 Ignition key cylinder illumination lamp output (high side)
 When the ignition key cylinder illumination lamp is ON
 System voltage
4
 -
 -
 -
 -
5
 DUN
 Output to central door locking (for unlocking the driver’s door)
 When the door lock actuators unlock the driver’s door
 System voltage
6
 DLK1&DLK2
 Output to central door locking (for locking the doors)
 When the door lock actuators lock the doors
 System voltage
7
 ASK2
 Power supply (fuse No. 23)

 Ignition switch: ACC
 System voltage
8
 CIG1
9
 MUT
 Power supply (fuse No. 11)
 Always
 System voltage

CONNECTOR: C-402




Terminal No.
 Terminal code
 Check item
 Check condition
 Normal condition
1
 TL2-2
 Side turn-signal lamp (LH) output <door mirror type>
 When side turn-signal lamp (LH) is ON
 System voltage
2
 IG1
 Power supply from ignition switch (IG1)
 Ignition switch: ON or START
 System voltage
3
 -
 -
 -
 -
4
 ACC
 Ignition switch (ACC) input
 Ignition switch: ACC
 System voltage
5
 IG11
 Power supply (fuse No. 15)
 Ignition switch: ON
 System voltage
6
 TAR3
 Tail lamp (RH) output
 When tail lamps are ON
 System voltage
7
 DLIP
 Output to central door locking (dead lock)
 When the door lock actuators unlock the front door
 System voltage
8
 -
 -
 -
 -

CONNECTOR: C-403




Terminal No.
 Terminal code
 Check item
 Check condition
 Normal condition
1
 GND
 Ground
 Always
 1 V or less
2
 RAD1
 Power supply (fuse No. 17)
 Always
 System voltage
3
 BUP1
 Power supply (fuse No. 18)
 Always
 System voltage
4
 TR2-2
 Side turn-signal lamp (RH) output <door mirror type>
 When side turn-signal lamp (RH) is ON
 System voltage
5
 IG+
 Power supply (fuse No. 10)
 Always
 System voltage
6
 -
 -
 -
 -
7
 MO
 Electric folding door mirror (unfolding) output
 When the electric folding door mirrors are unfolding
 System voltage
8
 -
 -
 -
 -
9
 MC
 Electric folding door mirror (folding) output
 When the door mirrors are folding
 System voltage
10
 ROOM
 Combination meter power supply
 Always
 System voltage

CONNECTOR: C-404




Terminal No.
 Terminal code
 Check item
 Check condition
 Normal condition
1
 HTR
 Blower motor output
 Blower motor in operation
 System voltage

CONNECTOR: C-405




Terminal No.
 Terminal code
 Check item
 Check condition
 Normal condition
1
 LIN2
 LIN communication line
 Always
 0 to 12 V (pulse signal)
2
 RLP-
 Room lamp output (low side)
 When room lamp is ON (duty)
 Pulse signal
3
 LP+1
 Room lamp output (high side)
 When the room lamp is ON
 System voltage
4 - 5
 -
 -
 -
 -
6
 SR+
 Power supply (fuse No. 9)
 Always
 System voltage
7
 -
 -
 -
 -

CONNECTOR: C-410




Terminal No.
 Terminal code
 Check item
 Check condition
 Normal condition
1
 +B2
 Battery 2
 Always
 System voltage
2
 +B1
 Battery 1
 Always
 System voltage

CONNECTOR: C-412




Terminal No.
 Terminal code
 Check item
 Check condition
 Normal condition
1
 F/PB
 Fuel pump power supply input
 Ignition switch: ON
 System voltage
2
 IODI
 +B power supply input
 Always
 System voltage

CONNECTOR: C-413




Terminal No.
 Terminal code
 Check item
 Check condition
 Normal condition
1
 4WDF
 Power supply (fuse No. 13)
 Always
 System voltage
2
 RWLO
 Output to rear wiper
 When rear wiper is operating
 System voltage
3
 RWF
 Rear wiper motor output
 When rear wiper is operating
 System voltage
4
 STLO
 Stop lamp switch power supply
 When tail lamp and high-mounted stop lamp is ON
 System voltage
5
 DLK3&DLK4
 Rear door lock output
 When rear door is locked
 System voltage
6
 -
 -
 -
 -
7
 DUL3&DUL4
 Rear door unlock output
 When rear door is unlocked
 System voltage
8
 RWAS
 Rear wiper auto stop switch input
 When rear wiper is operating
 System voltage

CONNECTOR: C-414




Terminal No.
 Terminal code
 Check item
 Check condition
 Normal condition
1
 DEFL
 Power supply (fuse No. 2)
 Ignition switch: ON
 System voltage
2
 F/P
 Fuel pump output
 Engine: Started
 System voltage
3
 -
 -
 -
 -

CONNECTOR: C-415




Terminal No.
 Terminal code
 Check item
 Check condition
 Normal condition
1
 SBR
 Rear height sensor power supply
 Ignition switch: ON
 4.2 to 5.7 V
2 - 7
 -
 -
 -
 -
8
 TRAT
 -
 -
 -
9
 DDR
 Front door switch (LH) input
 Front door switch (LH): ON (door open)
 1 V or less
10
 DAS
 Front door switch (RH) input
 Front door switch (RH): ON (door open)
 1 V or less
11
 DRH
 Rear door switch (RH) input
 Rear door switch (RH): ON (door open)
 1 V or less
12
 IG12&IG16
 Power supply (fuse No. 15)
 Ignition switch: ON
 System voltage
13
 BLP+
 Power supply (fuse No. 20)
 Ignition switch: ON
 System voltage
14
 BUP2
 Power supply (fuse No. 18)
 Always
 System voltage
15
 SHR
 Input from the rear height sensor
 Ignition switch: ON
 0.5 to 4.5 V
16
 -
 -
 -
 -
17
 SGR
 Rear height sensor earth
 Always
 1 V or less
18
 GTOP
 Input from tailgate lock release handle
 Tailgate lock release handle: ON
 1 V or less
19
 TRID
 Input from tailgate lock release handle
 Tailgate lock release handle: ON
 1 V or less
20
 DLH
 Rear door switch (LH) input
 Rear door switch (LH): ON (door open)
 1 V or less
21 - 22
 -
 -
 -
 -

CONNECTOR: C-416




Terminal No.
 Terminal code
 Check item
 Check condition
 Normal condition
1
 -
 -
 -
 -
2
 SHF
 Input from the front height sensor
 Ignition switch: ON
 0.5 to 4.5 V
3
 SGF
 Front height sensor earth
 Always
 1 V or less
4
 AMB-
 Earth (ambient temperature sensor)
 Always
 1 V or less
5
 MGL
 Headlamp levelling unit (LH) earth
 Always
 1 V or less
6
 MGR
 Headlamp levelling unit (RH) earth
 Always
 1 V or less
7
 SBF
 Rear height sensor power supply
 Ignition switch: ON
 4.2 to 5.7 V
8
 HWA
 Headlamp washer output
 When headlamp washer is ON
 1 V or less
9
 AMB+
 Ambient temperature sensor input
 Always
 0.2 - 2.72 V
10
 -
 -
 -
 -
11
 HLO
 Headlamp (LO) output
 When headlamp (LO) is ON
 1 V or less
12
 IG12&IG16
 Power supply (fuse No. 15)
 -
 -
13
 F/HI
 Cooling fan (HI) output
 When cooling fan HI is operating
 1 V or less
14
 -
 -
 -
 -
15
 IDRL
 Output to daytime running lamps
 Ignition switch: ON
 1 V or less
16
 N.HO
 Output to horn
 When horn sounds
 1 V or less
17
 HORN
 Output to security alarm horn
 When security alarm horn sounds
 1 V or less
18
 HHI
 Headlamp (HI) output
 When headlamp (HI) is ON
 1 V or less
19
 HOOD
 Input from hood latch switch
 Hood latch switch: ON (hood open)
 1 V or less
20
 BFSW
 Brake fluid switch input
 Brake fluid switch: ON
 1 V or less
21 - 22
 -
 -
 -
 -
23
 F/LO
 Cooling fan (LO) output
 When cooling fan LO is operating
 1 V or less
24
 MBL
 Headlamp levelling unit (LH) power supply
 Ignition switch: ON
 System voltage
25
 MBR
 Headlamp levelling unit (RH) power supply
 Ignition switch: ON
 System voltage
26
 MSL
 Output to the headlamp levelling unit (LH)
 Ignition switch: ON
 When the levelling motor is stopped
 1 V or less
When the levelling motor is operating
 16% to 84% of system voltage
27
 MSR
 Output to the headlamp levelling unit (RH)
 Ignition switch: ON
 When the levelling motor is stopped
 1 V or less
When the levelling motor is operating
 16% to 84% of system voltage
28
 -
 -
 -
 -

CONNECTOR: C-417




Terminal No.
 Terminal code
 Check item
 Check condition
 Normal condition
1
 5V
 Power supply (5V)
 Always
 5 V
2
 SIGR
 Keyless entry system signal output
 Always
 0 to 5 V (pulse signal)
3
 PWRC
 Receiver antenna module (door entry) power control
 Ignition switch: ON
 System voltage
4
 SIGI
 Immobilizer signal input/output
 When immobilizer authentication (When insert ignition key to ignition switch or turn ignition switch from ACC to ON.)
 0 to 5 V (pulse signal)
5
 WCLK
 Immobilizer CLOCK input
 When immobilizer authentication (When insert ignition key to ignition switch or turn ignition switch from ACC to ON.)
 0 to 5 V (pulse signal)
6
 SRSF
 Power supply (fuse No. 16)
 Ignition switch: ON
 System voltage
7 - 8
 -
 -
 -
 -
9
 DST+
 Cruise control switch (ACC distance) input
 Cruise control switch (ACC distance): ON
 1 V or less
10
 LDWS
 LDW switch input
 LDW switch: ON
 1 V or less
11
 DDUK
 Input to driver’s door lock actuator (unlock)
 Driver’s door lock: Unlocked
 1 V or less
12
 FIOS
 Hazard indicator assembly (ECO mode switch) input
 Hazard indicator assembly (ECO mode switch): ON
 1 V or less
13
 FCMS
 FCM switch input
 FCM switch: ON
 1 V or less
14
 LITI
 LIN communication line
 Always
 0 to 12 V (pulse signal)
15
 ASCS
 ASC off switch input
 ASC off switch: ON
 1 V or less
16
 CNML
 CAN-C-Mid_L
 -
 -
17
 CNMH
 CAN-C-Mid_H
 -
 -
18
 CANL
 CAN-C_L
 -
 -
19
 CANH
 CAN-C_H
 -
 -
20
 -
 -
 -
 -
21
 DATA
 LIN communication line
 Always
 0 to 12 V (pulse signal)
22
 AVCC
 Photo sensor power supply
 Ignition switch: ON
 5 V
23
 ASIG
 Photo sensor input
 Ignition switch: ON, Sensor illumination: Dark to Bright
 0 to approximately 4 V
24
 REQC
 Windshield wiper backup input
 Windshield low-speed wiper switch or windshield high-speed wiper switch: ON
 1 V or less
25
 MRR
 Input to remote controlled mirror switch (folding/unfolding switch)
 Remote controlled mirror switch (folding/unfolding switch): ON
 1 V or less
26
 HAZ
 Hazard switch input
 Hazard switch: ON
 1 V or less
27
 ADUK
 Input to front passenger’s door lock actuator (unlock)
 Front passenger’s door lock: Unlocked
 1 V or less
28
 D-LS
 Door lock switch (lock) input
 Power window main switch (door lock switch): Lock
 1 V or less
29
 -
 -
 -
 -
30
 HL1+
 Input to key reminder switch
 Key reminder switch: ON (ignition key removed)
 1 V or less
31
 D-US
 Door lock switch (unlock) input
 Power window main switch (door lock switch): Unlock
 1 V or less
32
 SEC
 Output to security indicator lamp
 When security indicator lamp is on
 1 V or less
33 - 34
 -
 -
 -
 -
35
 AGND
 Earth (photo sensor)
 Always
 1 V or less
36
 GND
 Ground
 Always
 1 V or less

CONNECTOR: C-418




Terminal No.
 Terminal code
 Check item
 Check condition
 Normal condition
1 - 2
 -
 -
 -
 -
3
 TAR2
 Tail lamp (RH) output
 When tail lamps are ON
 System voltage
4
 GLK
 Tailgate lock release handle output
 Tailgate lock release handle: ON
 System voltage
5
 TL3-1&TL3-2
 Rear turn-signal lamp (LH) output
 When rear turn-signal lamp (LH) is ON
 System voltage
6
 TAL2
 Tail lamp (LH) and licence plate lamp output
 With tail lamp and licence plate lamp illuminated
 System voltage
7
 -
 -
 -
 -
8
 PWS
 Rear power window sub switch power supply
 Ignition switch: ON
 System voltage
9
 DEAD
 Output to central door locking (dead lock)
 When the door lock actuators unlock the rear door
 System voltage
10
 RFOG
 Output to rear fog lamp
 Rear fog lamp is on
 System voltage
11
 TR3
 Rear turn-signal lamp (RH) output
 When rear turn-signal lamp (RH) is ON
 System voltage
12
 BLP2
 Back-up lamp switch or inhibitor switch power supply
 When back-up lamp is ON
 System voltage
13
 GLP-
 Output to luggage compartment lamp
 When luggage compartment lamp is illuminated
 Battery positive voltage

CONNECTOR: C-419




Terminal No.
 Terminal code
 Check item
 Check condition
 Normal condition
1
 IGN
 Engine ECU (IG1) output
 Ignition switch: ON
 System voltage
2
 WACC
 Windshield wiper (ACC) output
 Ignition switch: ACC
 System voltage
3
 BKLP
 Input from stop lamp switch
 Stop lamp switch: ON
 5 V
4
 FOGY
 Output to fog lamps
 Fog lamp switch: ON
 1 V or less
5
 ST2
 Ignition switch (START) switch output
 Ignition switch: START
 System voltage
6
 WASH
 Output to windshield washer
 When windshield washer is operating
 System voltage
7
 W.WA
 Rear washer output
 When rear washer is operating
 System voltage
8
 W.AS
 Windshield wiper auto stop switch input
 When windshield wipers are operating
 System voltage
9
 TR1&TR2-1
 Front turn-signal lamp and side turn-signal lamp (RH) <fender panel type> output
 With front and side turn-signal lamp (RH) illuminated
 System voltage
10
 TL1&TL2-1
 Front turn-signal lamp and side turn-signal lamp (LH) <fender panel type> output
 With front and side turn-signal lamp (LH) illuminated
 System voltage
11
 FP/R
 Engine ECU (fuel control) input
 Engine: Started
 1 V or less

CONNECTOR: C-420




Terminal No.
 Terminal code
 Check item
 Check condition
 Normal condition
1 - 2
 -
 -
 -
 -
3
 PWMB
 Power supply (fusible link No. 1)
 Ignition switch: ON
 System voltage
4 - 5
 -
 -
 -
 -
6
 DEF0
 Defogger output
 Defogger switch: ON
 1 V or less
7
 -
 -
 -
 -
8
 HOSW
 Horn switch input
 Horn switch: ON
 1 V or less
9
 ST
 Ignition switch (START) input
 Ignition switch: START
 System voltage
10
 SGND
 Ground
 Always
 1 V or less
11
 -
 -
 -
 -
12
 PWM
 Power supply (fusible link No. 20)
 Ignition switch: ON
 System voltage
13
 ACC1
 Power supply (fuse No. 22)
 Ignition switch: ACC
 System voltage

CONNECTOR: C-421




Terminal No.
 Terminal code
 Check item
 Check condition
 Normal condition
1
 STLD
 Stop lamp drive signal
 The ACC or the FCM activates, and the stop lamps illuminate.
 System voltage
2
 W.HI
 Windshield wiper (HI) output
 When windshield wipers are operating at high speed
 System voltage
3
 TAR1
 Position lamp (RH) output
 With position lamp ON
 System voltage
4
 -
 -
 -
 -
5
 BUP4
 Power supply (fuse No. 18)
 Ignition switch: ON
 System voltage
6
 STP
 Stop lamp switch power supply
 Stop lamp switch: ON
 System voltage
7
 W.LO
 Windshield wiper (LO) output
 When windshield wipers are operating at low speed
 System voltage
8
 TAL1
 Position lamp (LH) output
 With position lamp ON
 System voltage
9
 BLP1
 Inhibitor switch (R) input
 Selector lever: R and ignition switch: ON
 System voltage
10
 DEFR
 Defogger output
 Defogger switch: ON
 1 V or less

CONNECTOR: C-422




Terminal No.
 Terminal code
 Check item
 Check condition
 Normal condition
1
 SLSO
 Shift lock solenoid
 When all the following conditions are met.

  • Ignition switch: ON
  • Brake pedal: depressed
 System voltage