|
Q.
Is the check result normal?
|
|
Repair or replace the connector.
|
|
|
|
- Disconnect connector, and measure at the female side.
- Ignition switch: ON
- Voltage between terminal No. 12 and earth.
|
|
Q.
Is the check result normal?
|
|
- Disconnect engine-ECU connector, and connect special tool power plant ECU
check harness (MB992044) to measure at connector for inspection.
- Disconnect B-02 intermediate connector.
- Ignition switch: ON
- Voltage between terminal No. 13 and earth.
|
|
Q.
Is the check result normal?
|
|
Q.
Is the check result normal?
|
|
Check and repair harness between B-02 (terminal No.
12) intermediate connector and B-05 (terminal No. 13) engine-ECU connector.
- Check output line for open circuit.
|
|
|
|
Repair or replace the connector.
|
|
|
|
Q.
Is the check result normal?
|
|
Repair or replace the connector.
|
|
|
|
- Check output line for short circuit.
|
|
Q.
Is the check result normal?
|
|
Repair or replace the connector.
|
|
|
|
Q.
Does trouble symptom persist?
|
|
Intermittent malfunction (Refer to GROUP 00 - How to Use Troubleshooting/Inspection
Service Points - How to Cope with Intermittent Malfunctions ).
|
|
|
|
- Disconnect connector, and measure at the female side.
- Ignition switch: ON
- Voltage between terminal No. 6 and earth.
|
|
Q.
Is the check result normal?
|
|
Q.
Is the check result normal?
|
|
Repair or replace the connector.
|
|
|
|
- Check power supply line for open/short circuit.
|
|
Q.
Is the check result normal?
|
|
Repair the damaged harness wire.
|
|
|
|
- Disconnect connector, and measure at the female side.
- Resistance between terminal No. 5 and earth.
|
|
Q.
Is the check result normal?
|
|
Q.
Is the check result normal?
|
|
Repair or replace the connector.
|
|
|
|
- Check earthing line for open circuit and damage.
|
|
Q.
Is the check result normal?
|
|
Repair the damaged harness wire.
|
|
|
|
Q.
Is the check result normal?
|
|
Repair or replace the connector.
|
|
|
|
- Check power supply line for damage.
|
|
Q.
Is the check result normal?
|
|
Repair the damaged harness wire.
|
|
|
|
- Check output line for damage.
|
|
Q.
Is the check result normal?
|
|
Repair the damaged harness wire.
|
|
|
|
- Check output line for open/short circuit and damage.
|
|
Q.
Is the check result normal?
|
|
Repair the damaged harness wire.
|
|
|
|
- Check earthing line for open circuit and damage.
|
|
Q.
Is the check result normal?
|
|
Repair the damaged harness wire.
|
|
|
|
- Check power supply line for open/short circuit and damage.
|
|
Q.
Is the check result normal?
|
|
Repair the damaged harness wire.
|
|
|
|
Q.
Is the check result normal?
|
|
Replace the sensor wheel.
|
|
|
|
Q.
Does trouble symptom persist?
|
|
Replace the crank angle sensor.
|
|
|
|
Intermittent malfunction (Refer to GROUP 00 - How to Use Troubleshooting/Inspection
Service Points - How to Cope with Intermittent Malfunctions ).
|
|
|