REMOVAL AND INSTALLATION



Pre-removal and post-installation operation
  • Front deck garnish removal and installation (Refer to GROUP 51 - Windshield Wiper .)
  • Roof drip moulding removal and installation (Refer to GROUP 51 - Moulding .)
  • Front pillar trim removal and installation (Refer to GROUP 52A - Interior Trim .)
  • Inside rear view mirror assembly removal and installation (Refer to GROUP 52A - Inside Rear View Mirror .)






Removal steps
<<A>>
>>B<<
1.
Windshield


2.
Windshield moulding

>>A<<
3.
Glass stopper

>>A<<
4.
Windshield spacer

REMOVAL SERVICE POINTS



<<A>> WINDSHIELD REMOVAL


1.In order to protect the body (paint surface), apply a cloth tape to the body area along the windshield opening.

2.When separating adhesive using a piano wire
(1) Use a knife to cut away the moulding.
(2) Use a sharp-point drill to make a hole in the windshield adhesive.
(3) Pass the piano wire from the inside of the vehicle through the hole.
(4)
caution Do not let the piano wire touch the edge of the windshield.
Pull the piano wire alternately from the inside and outside along the windshield to cut the adhesive.


3.When separating adhesive using a windshield knife
(1) Using glass adhesive knife
(2)
caution If you lever the windshield knife, the windshield may be damaged.
Holding the tip of the windshield knife and the windshield edge at right angles, align the blade of the windshield knife with the windshield surface and edge, and pull the blade parallel to the edge to separate the adhesive.

4.Make mating marks on special tool windshield and body, and use the window glass holder (MB990480) to remove the windshield.

5.
caution
  • Be careful not to remove more adhesive than is necessary.
  • Be careful also not to damage the paintwork on the body surface with the knife. If the paintwork is damaged, repair the damaged area with repair paint or anti-rust agent.
Use a knife to cut away the remaining adhesive so that the thickness is within 2 mm around the entire circumference of the body flange.
6.Finish the flange surfaces so that they are smooth.
7.If the windshield is reused, scrape away all traces of old adhesive, the glass stopper, and the windshield spacer.

INSTALLATION SERVICE POINTS



>>A<< WINDSHIELD SPACER/GLASS STOPPER INSTALLATION


1.
caution Before the next operation, leave the decreased parts for 3 minutes or more to dry. Do not touch the coated surface.
Use white gasoline to degrease the inside circumference of the windshield and the body flanges.
2.

Position the windshield spacer, ensuring that there are no bends or looseness inside the windshield.
3.Secure the glass stoppers to the specified positions on the windshield.

>>B<<WINDSHIELD INSTALLATION


1.Install the windshield moulding to the windshield.
2.To replace the windshield, temporarily set the windshield against the body, and place mating marks on the body and windshield.
3.
caution
  • The primer strengthens the adhesive, so be sure to apply it. However, a too thick application will weaken the adhesive.
  • Do not touch the coated surface.
  • Do not apply the primer on the remaining adhesive. The adhesive strength may be weakened.
Soak a sponge in the primer, and apply evenly to the windshield and the body in the specified places.
4.After applying the primer, let it dry for 3 minutes or more.

5.Fill a sealant gun with adhesive. Then apply the adhesive evenly around the windshield within 30 minutes after the primer application.
note Cut the tip of the sealant gun nozzle into a V shape to simplify adhesive application.
6.After applying the adhesive, align the mating marks on the windshield and the body, and then press the windshield gently to seat it.
7.Use spatula or the like to remove any excessive adhesive. Then clean the surface with white gasoline. Leave the vehicle stationary until the adhesive sets (Refer to Rest time after operation ).
8.
caution
  • Move the vehicle carefully.
  • When testing for water leakage, do not pinch the end of the hose to spray the water.
Wait 30 minutes or more, and then test for water leakage.

INSPECTION EMBLEM REMOVAL AND INSTALLATION


1.Use your hands or a plastic spatula to remove the inspection emblem.
2.Remove the remaining adhesive using diluted mild detergent for home use or inorganic solution (alcohol).
3.Attach the new inspection emblem to the specified position.