ID CODES REGISTRATION PROCEDURE



The ID codes necessary for the engine immobiliser system and the keyless entry system can be registered by operating on the M.U.T.-III screen.
caution
  • When the door lock cylinder or the glove box lock cylinder is replaced as a single unit, do not register the bar code No. attached to the ignition key. If registered, starting the engine by using the conventional key becomes impossible. The new key will not be able to start the engine, too, because it has a different key groove.
  • If the ignition key with transmitter is added or replaced, register the key (key ID), and then register the keyless entry secret code again.

Key supply unit
Ignition key (without transmitter)
Ignition key (with transmitter)
note Blank key (It is the key that comes with the door service key set, tailgate service key set and the glove box service key set. It can only be used for locking and unlocking, and it cannot start the engine.)








KEY SUPPLY UNIT LIST FOR OTHER THAN INDIVIDUAL KEY
Full service key set
Handle lock service key set
Door service key set
Glove box service key set
Tailgate service key set










*: Vehicles for dead lock system
note
  • When re-registering the key (key ID), all the keys (key ID) registered before must be re-registered because all of them will be erased.
  • When the ignition key was replaced by the full service key set or when the ignition key was replaced by the handle lock service key set separately, register the key (key ID) using the barcode No. attached to the key.
  • If the handle lock service key set, door service key set, tailgate service key set or glove box service key set is replaced as a unit, two kinds of keys are used (the key that starts the engine and the key that opens and closes the doors). To use only one key, replace the ignition key by the full service key set instead of replacing it by a unit.
  • After registering the keys, make sure that the engine is started normally with all of the keys registered.




Connect the M.U.T.-III to the 16-pin diagnosis connector as follows.
note For details on how to use the M.U.T.-III, refer to the "M.U.T.-III User’s Manual."
1.Start the M.U.T.-III system on the PC and turn the ignition switch to the "ON" position.
2.

Select "IMMOBI/KOS/Keyless" button from the "System Select" screen. Then, select the applicable option code item and push the OK button.

3.Select "Special Function" on the next screen.
4.

Select the button of the operation to be performed from the "Special Function" screen.

note For "Key Code Registration," refer to GROUP 00 - Precautions before Service .

KEY REGISTRATION METHOD


1.

When "Key registration" screen is displayed, enter the password for the key registration and press the OK button. Then, "Executing!" is displayed and the registration process starts.
note
  • If the wrong password is entered consecutively 5 times, the password entry for the key registration will be disabled for 16 minutes.
  • The key registration cannot be cancelled during the operation.
2.

When the key registration is completed, "Completed" is displayed. To register the next key, follow the message on the screen and press the OK button. Then, "Executing!" is displayed again and the registration process for the next key starts. To finish the key registration, press the cancel button.
note
  • In order to register another key consecutively after registering the first key, the ignition switch must be turned to the ON position with the second key within 30 seconds after turning it to the "LOCK" (OFF) position with the first key.
  • Up to eight keys can be registered.

KEY REGISTRATION (BARCODE NO.) METHOD


1.

When "Key Registration (Barcode No.)" screen is displayed, enter the password for the key registration and press the OK button.
note If the wrong password is entered consecutively 5 times, the password entry for the key registration will be disabled for 16 minutes.
2.


Follow the message on the screen to enter the barcode No., and then press the OK button.
3.When "Do you want to start registration?" is displayed, press the OK button to start the registration, or press the Cancel button to cancel the registration.
4."Key Registration was completed" is displayed. Press the OK button to finish the registration.

"KEYLESS ID REGISTRATON" METHOD


1.

On the "Keyless ID Registration" screen, enter the password and press the OK button.
2.Register within 1 minute and send the programing packet* to register the keyless ID. To register multiple keys, register the next key within 1 minute from the registration operation of previous key. Complete the registration of necessary keys, then press the OK button to finish the keyless ID registration.
note
  • Up to eight ignition keys can be registered.
  • *: Programming packet sending procedure
    Complete the following steps 1 to 3 within four seconds.

    1. Press and hold both the lock and the unlock switch for 1 second or longer.
    2. Release both the lock and the unlock switch for 0.5 second or longer.
    3. Press the unlock switch.
3.Push the OK button after "Keyless ID Registration was finished." is displayed.
4.

Check number of the keyless IDs registered.