CODE NO. B1B22 Right curtain air bag module (squib) system (open circuit of squib circuit)










caution If the diagnosis code B1B22 is set to SRS-ECU, be sure to diagnose the CAN bus line.

OPERATION
In case of side collision, when the impact exceeding the threshold is applied to the vehicle, and when the impact is simultaneously detected (turned ON) by the side impact sensor installed to the lower part of centre pillar and to quarter panel inner as well as by the side-airbag safing G-sensor in SRS-ECU, the electric current is supplied from SRS-ECU to the curtain air bag module (squib) of impacted side.

TROUBLE JUDGMENT
The code is set when the open circuit occurs to the SRS-ECU curtain air bag module (squib) circuit.

PROBABLE CAUSES

  • Open circuit to the curtain air bag module (squib) circuit
  • Damaged connector(s)
  • Malfunction of SRS-ECU

DIAGNOSIS PROCEDURE

STEP 1. M.U.T.-III CAN bus diagnostics.
Use M.U.T.-III to diagnose the CAN bus lines.

Q. Is the check result normal?
Go to Step 2.
Repair the CAN bus line (Refer to GROUP 54C - Troubleshooting ).

STEP 2. Check whether the diagnosis code is reset.
(1)Connect the negative battery terminal.
(2)After erasing the diagnosis code memory, check the diagnosis code again.
(3)Disconnect the negative battery terminal.

Q. Is the diagnosis code No. B1B22 set?
Go to Step 3.
Intermittent malfunction (Refer to GROUP 00 - How to Use Troubleshooting/Inspection Service Points - How to Cope with Intermittent Malfunction ).

STEP 3. Diagnosis check by dummy resistor connection.
(1)Check that the negative battery terminal is disconnected. If the negative battery terminal is connected, disconnect it.
(2)Disconnect the D-08 intermediate connector (connection between curtain air bag harness and floor harness).

(3)Connect special tool dummy resistor (MB991865) to special tool resistor harness (MB991866).
(4)
caution Do not insert a probe directly into the terminal from the connector front side as the connector contact pressure may be weakened.
Insert the probe of resistor harness, to which the dummy resistor is installed, from the back of D-08 intermediate connector (floor harness side).
(5)Connect the negative battery terminal.
(6)After erasing the diagnosis code memory, check the diagnosis code again.
(7)Disconnect the negative battery terminal.

Q. Is the diagnosis code No. B1B22 set?

Go to Step 4.

Go to Step 5.

STEP 4. Resistance measurement at the C-31 SRS-ECU connector and the D-08 intermediate connector.
(1)Check that the negative battery terminal is disconnected. If the negative battery terminal is connected, disconnect it.

(2)While pushing the part "A" indicated in the figure of the harness side connector, turn the lock lever to the direction of the arrow to release the lock lever, and disconnect the C-31 SRS-ECU connector.
(3)Disconnect the D-08 intermediate connector (connection between curtain air bag harness and floor harness).
(4)
caution Do not insert a probe directly into the terminal of D-08 intermediate connector from the connector front side as the connector contact pressure may be weakened.
Check the continuity between the C-31 harness side connector terminal No. 39 and the D-08 intermediate connector (floor harness side) terminal No. 2.
(5)Check the continuity between the C-31 harness side connector terminal No. 40 and the D-08 intermediate connector (floor harness side) terminal No. 1.
OK: Continuity (less than 2 Ω)

Q. Is the check result normal?

Go to Step 6.

Repair the wiring harness between the C-31 harness side connector terminal No. 39/40 and the D-08 intermediate connector (floor harness side) terminal No. 2/1.

STEP 5. Resistance measurement between the D-08 intermediate connector terminal No. 1/2 and the D-103 curtain air bag module harness side connector terminal No. 1/2.
(1)Check that the negative battery terminal is disconnected. If the negative battery terminal is connected, disconnect it.
(2)Disconnect the D-08 intermediate connector (connection between curtain air bag harness and floor harness).

(3)Use the flat-tipped screwdriver to pull out the locking button of harness side connector. After releasing the lock, disconnect the D-103 harness side connector.

(4)Connect special tool resister harness (MB991884) to the removed D-103 harness side connector.
(5)
caution Do not insert a probe directly into the terminal of D-08 intermediate connector from the connector front side as the connector contact pressure may be weakened.
Check the continuity between the D-08 intermediate connector (curtain air bag harness side) terminal No. 1 and the resistor harness connector terminal No. 2.
(6)Check the continuity between the D-08 intermediate connector (curtain air bag harness side) terminal No. 2 and the resistor harness connector terminal No. 1.
OK: Continuity (less than 2 Ω)

Q. Is the check result normal?

Replace the curtain air bag module (squib) (Refer to ).

Repair the wiring harness.

STEP 6. Check whether the diagnosis code is reset.

Q. Is the diagnosis code No. B1B22 set?
Replace SRS-ECU (Refer to ).
Intermittent Malfunction (Refer to GROUP 00 - How to Use Troubleshooting/Inspection Service Points - How to Cope with Intermittent Malfunction ).