Tool
| Number
| Name
| Use
|
| MB990590
| Rear axle shaft oil seal remover
A: Adapter
B: Sliding hammer
|
- Removal of differential carrier oil seal
- Removal and installation of inner shaft (Used together with MB990906)
|
| MB990767
| Front hub and flange yoke holder
|
- Hub fixing
- Removal and installation of companion flange
|
| MB991618
| Hub bolt remover
| Removal of hub bolt
|
| MB991897 or MB992011
| Ball joint remover
| Knuckle and tie rod end ball joint disconnection
| note | Steering linkage puller (MB990635 or MB991113)is also used to disconnect knuckle and tie
rod end ball joint.
|
|
| A: MB990998
B: MB991000
| A: Front hub remover and installer
B: Spacer
|
- Measurement of hub starting torque
- Measurement of wheel bearing axial play
|
| MB990843
| Drag link bushing remover and installer A
|
| MB990326
| Preload socket
|
- Inspection of hub rotation starting torque
- Measurement of wheel bearing turning torque
|
| MB991561
| Boot band crimping tool
| Resin boot band installation
|
| MB990906
| Driveshaft attachment
| Removal and installation of inner shaft (Used together with MB990211)
|
| MB990560
| Bearing remover
|
- Removal and press-fitting of inner shaft bearing
- Removal of freewheel clutch bearing
|
| MB990955
| Oil seal installer
| Press-fitting of housing tube dust seal (Used together with MB990938)
|
| MB991168
| Differential oil seal installer
| Installation of freewheel clutch oil seal
|
| MB990799
| Ball joint Remover and installer A
| Installation of freewheel clutch bearing
|
| MB990890 or MB990891
| Rear suspension bushing base
|
| MB990909
| Working base
| Supporting of front differential carrier assembly
|
| MB991116
| Adapter
| Supporting of front differential carrier assembly
|
| MB990810
| Side bearing puller
|
- Remove of side bearing inner race
- Remove of companion flange
|
| MB990811
| Differential side bearing cap
|
| MB990339
| Bearing puller
| Removal of drive pinion front bearing inner race
|
| MB990648
| Bearing remover
|
| MB990685
| Torque wrench
|
- Inspection of hub rotation starting torque
- Measurement of wheel bearing turning torque
|
| MB991171
A: MB990819
B: MB991170
C: MB991169
| Pinion height gauge set
A: Drive pinion gauge assembly
B: Cylinder gauge
C: Attachment
|
- Inspection of drive pinion rotation starting torque
- Measurement of drive pinion height
|
| MB990802
| Bearing installer
|
- Press-fitting of drive pinion front bearing inner race
- Press-fitting of side bearing inner race
|
| MB990031 or MB990699
| Drive pinion oil seal installer
| Press-fitting of drive pinion oil seal
|
| MD999547
| Oil seal installer
| Removal of front differential mount insulator Front side, Rear side (LH)
|
| MB990947
| Lower arm bushing arbor
| Press fitting of front differential mount insulator
Front side, Rear side (LH)
|
| MB990847
| Rear suspension bushing remover and installer base
|
| MB990981
| Mount bushing remover and installer
|
| MB990925
| Bearing and oil seal installer set
|
- Press-fitting of wheel bearing outer race
- Press-fitting of oil seal (differential carrier)
- Press-fitting of drive pinion rear bearing outer race
- Press-fitting of drive pinion front bearing outer race
- Oil seal installation (free wheel clutch)
|
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)