Code No.B1421: Side-airbag squib (RH) open-circuited

caution

If diagnosis code B1421 is set in the SRS-ECU, always diagnose the CAN bus lines.

OPERATION

The SRS-ECU judges how severe a collision is by detecting signals from the left and right side impact sensors. If the impact is over a predetermined level, the SRS-ECU sends an ignition signal. At this time, if the side-airbag safing G-sensor is on, the SRS side-airbag will inflate.
The ignition signal is input to the side-airbag module to inflate the side-airbag.

DIAGNOSIS CODE SET CONDITIONS

This diagnosis code is set if there is abnormal resistance between the input terminals of the side-airbag module (RH) (squib).

PROBABLE CAUSES

Open circuit in the side-airbag module (RH) (squib) circuit
Improper connector contact
Malfunction of the SRS-ECU

DIAGNOSIS PROCEDURE

STEP 1. M.U.T.-III CAN bus diagnostics

Use the M.U.T.-III to diagnose the CAN bus lines.

Q. Is the check result normal?

	Go to Step 2

	Repair the CAN bus lines (Refer to GROUP 54D, Diagnosis).

STEP 2. Check whether the diagnosis code is reset.

Check again if the diagnosis code is set.

(1)Erase the diagnosis code.

(2)Ignition: "LOCK" (OFF) position to "ON"

(3)On completion, check that the diagnosis code is not reset.

Q. Is the diagnosis code set?

	Go to Step 3.

	There is an intermittent malfunction such as poor engaged connector(s) or open circuit (Refer to GROUP 00, How to Cope with Intermittent Malfunction ).

STEP 3. Check the side-airbag module (RH).

(1)Disconnect the negative battery terminal.

(2)Disconnect the side-airbag module (RH) connector E-127.

(3)Connect special tool dummy resistor (MB991865) to special tool resistor harness (MB991866).
(4)

caution

Do not insert a test probe into the terminal from its front side directly, as the connector contact pressure may be weakened.

Insert special tool MB991866 into the E-127 harness side connector by backprobing.
(5)Connect the negative battery terminal.
(6)Erase the diagnosis code from memory, and check the diagnosis code.

Q. Is diagnosis code B1421 set?

Go to Step 4.

Replace the front seatback assembly (RH) (Refer to GROUP 52A, Front Seat

STEP 4. Resistance measurement between SRS-ECU connector D-23 (terminal No.57 and 58) and the side-airbag module (RH) connector E-127 (terminal No.2 and 1).

(1)Disconnect the negative battery terminal.

(2)Disconnect SRS-ECU connector D-23.

(3)

danger

To prevent the air bag from deploying unintentionally, disconnect the side-airbag module (RH) connector E-127 to short the squib circuit.

Disconnect side-airbag module (RH) connector E-127.

(4)

caution

Insert an insulator such as a cable tie to a depth of 4 mm or more, otherwise the short spring will not be released.

Insert a cable tie [3 mm wide, 0.5 mm thick] between terminals 57, 58 and the short spring to release the short spring.
(5)

caution

Do not insert a test probe into the terminal from its front side directly, as the connector contact pressure may be weakened.

Check for continuity between the following terminals.

SRS-ECU connector D-23 (terminal No.57) and the side-airbag module (RH) connector E-127 (terminal No.2)
SRS-ECU connector D-23 (terminal No.58) and the side-airbag module (RH) connector E-127 (terminal No.1)

OK: Continuity (Less than 2 Ω)

Q. Are the check results normal?

Go to Step 5.

Repair the harness wires between SRS-ECU connector D-23 (terminal No.57 and 58) and side-airbag module (RH) connector E-127 (terminal No.2 and 1).

STEP 5. Check whether the diagnosis code is reset.

Q. Is diagnosis code B1421 set?

	Replace the SRS-ECU (Refer to ).

	An intermittent malfunction is suspected (Refer to GROUP 00, How to Cope with Intermittent Malfunction ).