If diagnosis code U1109 is set in the engine-A/T-ECU,
always diagnose the CAN main bus line. If there is any fault in the CAN bus lines, an incorrect
diagnosis code may be set.
Whenever the ECU is replaced, ensure that the communication circuit is normal.
DIAGNOSIS CODE SET CONDITIONS
Current trouble
Connector(s) or wiring harness in the CAN bus lines between the ETACS-ECU and the
engine-A/T-ECU, the power supply system to the ETACS-ECU, the ETACS-ECU itself, or
the engine-A/T-ECU may be defective.
Past trouble
Carry out diagnosis with particular emphasis on connector(s) or wiring harness in
the CAN bus lines between the ETACS-ECU and the engine-A/T-ECU, and the power supply system
to the ETACS-ECU. For diagnosis procedures, refer to "How to cope with past trouble" (Refer
to GROUP 00, How to Use Troubleshooting/Inspection Service Points ).
note
For a past trouble, you may not find it by the M.U.T.-III CAN bus diagnostics even if
there is any failure in CAN bus lines. In this case, refer to GROUP 00, How to Use Troubleshooting/Inspection
Service Points - How to Cope with Intermittent Malfunctions ).
and check the CAN bus lines. You can narrow down the possible cause of the trouble by referring
to the diagnosis code, which is set regarding the CAN communication-linked ECUs (Refer to GROUP 54C,
Explanation about the M.U.T.-III CAN Bus Diagnostics ).
PROBABLE CAUSES
Damaged wiring harness or connector
Malfunction of the ETACS-ECU
Malfunction of the engine-A/T-ECU
DIAGNOSIS PROCEDURE
STEP 1. M.U.T.-III CAN bus diagnostics
Using M.U.T.-III, perform CAN bus line diagnosis.
Q.
Is the check result normal?
Go to Step 2.
Repair the CAN bus line (Refer to GROUP54C, Diagnosis - Can Bus Diagnostic
Chart ), and then go to Step 6.
STEP 2. M.U.T.-III other system diagnosis codes
Check whether the local interconnect network (LIN) system diagnosis codes are set or not.
Q.
Is the diagnosis code set?
Diagnose the ETACS system (Refer to GROUP 54A, Troubleshooting ).
Go to Step 3.
STEP 3. M.U.T.-III other system diagnosis codes
Check if a diagnosis code, which relates to CAN communication-linked systems below, is
set.
Engine-ECU: Code No.U1109
Q.
Is the diagnosis code set?
Go to Step 4.
Go to Step 5.
STEP 4. M.U.T.-III diagnosis code
Reconfirm whether the diagnosis codes are output from engine-A/T-ECU.
(1)Erase the diagnosis code.
(2)Turn the ignition switch to ON position.
(3)Check if the diagnosis code is set.
Q.
Is the diagnosis code set?
Replace ETACS-ECU. Then go to Step 6.
Intermittent malfunction in CAN bus line between ETACS-ECU and engine-A/T-ECU
(Refer to GROUP 00 - How to Use Troubleshooting/Inspection Service Points ).
STEP 5. M.U.T.-III diagnosis code
Reconfirm whether the diagnosis codes are output from engine-A/T-ECU.
(1)Erase the diagnosis codes being set.
(2)Ignition switch: LOCK (OFF) to ON
(3)Confirm whether the diagnosis codes are set.
Q.
Is the diagnosis code set?
Replace engine-A/T-ECU. Then go to Step 6.
Intermittent malfunction in CAN bus line between ETACS-ECU and engine-A/T-ECU
(Refer to GROUP 00 - How to Use Troubleshooting/Inspection Service Points ).
STEP 6. M.U.T.-III diagnosis code
Reconfirm whether the diagnosis codes are output from engine-A/T-ECU.
).
